Description
Miller PipeWorx 400 Welding System Package 951000094
The Miller PipeWorx 400 is a compleate 400 amp multi-process welding solution for your pipe welding fab shop. From root pass to cap pass, the PipeWorx 400 allows you to seamlessly switch between welding processes and/or filler metals. For MIG welding, the PipeWorx Dual-Wire Feeder provides unsurpassed bead control with advanced pulsed-MIG and RMD (Regulated Metal Deposit). Left and right MIG gun select allows you to switch back and forth between different filler metals, shielding gases and weld parameters with the touch of a button.
Does your job require stick or TIG welding for any of your pipe welding passes? No problem. The PipeWorx 400 has dedicated stick and TIG welding output studs, so there’s no need to disconnect and reconnect OPTIONAL stick welding lead or TIG torch. In stick welding mode, the PipeWorx 400 produces an outstanding arc when using either E6010 or E7018 stick electrodes. For DC TIG, the PipeWorx offers both Lift-Arc and high frequencty arc starts. There is also a dedicated TIG shielding gas port on the front panel of the welder. Should your job require a water cooler, a 115 volt outlet is also located on the front panel.
This PipeWorx 400 operates on three-phase, 230/460 volt input power. The included PipeWorx Dual-Wire Feeder comes complete with digital meters, soft keys and memory buttons – plus advanced features like pulsed-MIG, RMD, pre-programmed parameters for advanced MIG welding; plus two MIG gun ports, two sets of drive rolls and spool wire spindles. The complete PipeWorx package includes PipeWorx 400 welder, PipeWorx Dual-Wire Feeder, two Bernard PipeWorx 300 amp MIG guns, running gear with dual cylinder rack, two flowmeter/regulators, 25 ft. ground cable with clamp and all interconnecting cables and gas hoses.
Processes
Applications
Heavy Industrial Applications
Process piping
Refinery
Petrochemical
Power plants
HVAC and water pipe
Features
Setting up a new weld processis simple, requiring fewer steps,less training, and minimizingpotential errors.
The front panel was designedby welders for welders. Onlybacklit controls are adjustableto eliminate confusion.
The memory feature storesfour programs for stick, DC TIG,and wire processes (left andright feeder side) each.
Innovative cable and gun storagemaintains an organized weld-cellarea. Cables stay connected tothe power source, eliminatingthe need for switching betweenwelding processes.
All system components aretailored to meet the demands ofa pipe fabrication shop
Includes conventional stick,DC TIG (Lift-Arc or HF start),flux-cored and MIG weldingprocesses.
Features advanced RMD andpulsed MIG processes forhigh-quality welds, enhancedproductivity, and less reworkand training.
PipeWorx Quick-Selecttechnology auto-chooseswelding process, polarity,cable outputs, and parameters.
Eliminates set-up time forswitching cables and gas hoses
Memory cardsaves process parameters of allmemory locations. Each operator canhave their own machine settings.
Automaticallysets the optimum welding conditionsfor common E6010 series and E7018low hydrogen series electrodes.
Provide optimum pipe weldingperformance. Choose from FCAW,MIG, RMD and pulsed MIG. RMDmodified short circuit and pulsedMIG are synergic programs.
Are optimizedbased on selection of wire type,wire diameter and shielding gas type.No setting required.
For eachselection: stick, TIG, MIG (left andright). This eliminates the need toremember parameters.
Select between highfrequency or Lift-Arc with the pushof a button.
Trigger select allows the welder toselect a stored parameter withoutreturning to the power source.
Provide systemprotection in the dusty environmentof a pipe shop.
Built-in TIG gas solenoid automaticallyturns gas on/off in HF or Lift-Arc mode.
Forwater cooler, if used.
Comes complete with
Reviews
There are no reviews yet.